PF-Elcon

News

More News Releases

18-1-2010
From 18 January 2010, Pepperl+Fuchs Elcon s.r.l. becomes Pepperl+Fuchs s.r.l.
more info

13-1-2010
Pepperl+Fuchs has acquired Walsall Ltd. to expand the Process Automation Division by knowl
more info

16-12-2009

more info

Forum

Soon will be available a Forum where you'll find interesting info regarding the world of Process Automation.

Remote I/O System “Point to Bus” I/O

“Point to Bus” System
HiD3000 with integral Instrinsic Safety, drastically reduces field cabling and saves cabinet space.
HiD3000 termination boards can even be installed in a “Zona 2” hazardous area and accept inputs from “Zona 0” with the isolated intrinsic safety inputs.

Plug & Play Modules
Plug & Play module allows to mix I/O signal types to match all field applications. Analog and digital signals can be mixed in any combination on each termination board, avoiding the need to marshal field wiring.

Conversion of the process signal into digital from takes place within every HiD3000 module, eliminating external signal to signal conversion and increasing overall loop accuracy.

Download full datasheet (PDF) | Installation sheet (PDF)

Field Device	Model	No. of Ch. Part Number	Hazardous Area Signal	Comment
Analog IN/OUT	HiD3010	Ch. 2 - PN 186323	4-20 mA (15 V) floating supply to Smart or non-Smart two wire Transmitters.	Channels may be either: 2 analog inputs or 2 analog outputs or 1 analog input + 1 analog output.
Analog IN/OUT	HiD3010	Ch. 2 - PN 186323	4-20 mA signal to I/P converters, electrovalve actuators and displays.	HART® signals are routed to external multiplexer and hand held communicator (HHC).
Low Level IN	HiD3040	Ch. 4 - PN 186324	Thermocouple or mV.	Configurable for mV; TC; RTD or Pot inputs (2-3-4 wire).
Low Level IN	HiD3040	Ch. 2 - PN 186324	RTD or Potentiometer.	Configurable for mV; TC; RTD or Pot inputs (2-3-4 wire).
Digital IN	HiD3824	Ch. 4 - PN 186322	Dry Contact or Proximity Switch.	Each channel configurable for Line Fault Detection.
Digital OUT	HiD3878	Ch. 2 - PN 186320	40 mA at 11 V to drive a solenoid valve, audible or visual alarm (LED).	Each channel configurable for Line Fault Detection.
Frequency IN	HiD3891	Ch. 1 - PN 186325	Frequency measurement unit with “proximity switch” or “voltage input” electrical interface.	Up to 2 KHz input frequency programmable integration time (≥ 1 second) line fault detection (open and short circuit).
Communication Gateway	PBDP1	PN 186326	Profibus DP slave module.	All PROFIBUS DP data rates up to 12 M bit/sec.
Communication Gateway	MBRT	PN 186318	Modbus RTU slave module.	All MODBUS RTU slave, data rates up to 115.2 K bit/sec.
HART® Multiplexer	MUX2700	Ch. 32

Standard Termination Boards

Intrinsic Safety 16 position Termination Board

Model:
3116/HAT-2G/SABUS-R-HART (PN129647).

Board configuration:
- 1 to 16 modules HiD3000.
- 1 or 2 Gateways Modbus RTU or Profibus DP.
- 1 MUX2700 HART® Multiplexer (optional).

Connection:
- Hazardous Area 9 blue terminals per module (including shield).
- Safe Area: Fieldbus Communication Link.
- Power Supply: Redundant terminals for 24 Vdc supply.
- RS232 connectors for local access to each communication Gateway.
- Test Points accessing each HART® signal.
- RS485 connection terminals for MUX2700 connections HART® Multiplexer (identified as A, B, GND) 6 terminals for multidrop.

Mounting:
- Safe or Hazardous Area (Zone 2) location.
- Surface mounting or DIN-rail 35 mm using DINK1 accessory.

Non I.S. 16 position Termination Board

Model:
3116/FCT-2G/SABUS-R-HART (PN473202).

Board configuration:
- 1 to 16 modules HiD3000.
- 1 or 2 Gateways Modbus RTU or Profibus DP.
- 1 MUX2700 HART® Multiplexer (optional).

Connection:
- Field instrumentation: 9 grey terminals per module (including shield).
- System: Fieldbus Communication Link.
- Power Supply: Redundant terminals for 24 Vdc supply.
- RS232 connectors for local access to each communication. Gateway
- Test Points accessing each HART® signal.
- RS485 connection terminals for MUX2700 connections HART® Multiplexer (identified as A, B, GND) 6 terminals for multidrop.

Mounting:
- Safe Area location.
- Surface mounting or DIN-rail 35 mm using DINK1 accessory.

I.S. and non-I.S. 15 position Termination Board

Model:
3115/10HAT-5FCT-2G/SABUS-R-HART (PN130299).

Board Configuration:
- 1 to 15 modules HiD3000.
- 1 or 2 Gateways Modbus RTU or Profibus DP.
- 1 MUX2700 HART® Multiplexer (optional).

Connection:
- Field instrumentation:
- Hazardous Area: 10 modules, each one connecting to 9 blue terminals (including shield).
- Safe Area: 5 modules, each one connecting to 9 grey terminals (including shield).
- System: Fieldbus Communication Link.
- Power Supply: Redundant terminals for 24 Vdc supply.
- RS232 connectors for local access to each communication Gateway.
- Test Point accessing each HART® signal.
- RS485 connection terminals for MUX2700 connections HART® Multiplexer (identified A, B, GND) 6 terminals for multidrop.

Mounting:
- Safe Area location.
- Surface mounting or DIN-rail 35 mm using DINK1 accessory.

Intrinsic Safety 8 position Termination Board

Model:
3108/HAT-2G/SABUS-R-HART (PN130300).

Board configuration:
- 1 to 8 modules HiD3000.
- 1 or 2 Gateways Modbus RTU or Profibus DP.
- 1 MUX2700 HART® Multiplexer (optional).

Connection:
- Hazardous Area: 9 blue terminals per module (including shield).
- Safe Area: Fieldbus Communication Link.
- Power Supply: Redundant terminals for 24 Vdc supply.
- RS232 connectors for local access to each communication. Gateway.
- RS485 connection terminals for MUX2700 connections HART® Multiplexer (identified as A, B, GND) 6 terminals for multidrop.

Mounting:
- Safe or Hazardous Area (Zone 2) location.
- Surface mounting or DIN-rail 35 mm using DINK1 accessory.

Non I.S. 8 position Termination Board

Model:
3108/FCT-2G/SABUS-R-HART (PN473200).

Board configuration:
- 1 to 8 modules HiD3000.
- 1 or 2 Gateways Modbus RTU or Profibus DP.
- 1 MUX2700 HART® Multiplexer (optional).

Connection:
- Field instrumentation: 9 blue terminals per module (including shield).
- System: Fieldbus Communication Link.
- Power Supply: Redundant terminals for 24 Vdc supply.
- RS232 connectors for local access to each communication Gateway.
- RS485 connection terminals for MUX2700 connections HART® Multiplexer (identified as A, B, GND) 6 terminals for multidrop.

Mounting:
- Safe Area location.
- Surface mounting or DIN-rail 35 mm using DINK1 accessory.

Approvals
Authority	Certificate/File no.	Standard	Approved for	PDF
	CESI 03 ATEX 061	EN 50.014 EN 50.020 EN 50.284 EN 50.021	II (1) GD [EEx ia] IIC II 3 (1) GD - EExnA IIC; T4
	1222682	C22.2 No. 157 C22.2 No. 213 E79-0 E79-11 E79-15	Cl. I, Div. 1; Cl. I, Zone O: [Exia] IIC. Cl. I, Div. 2 Cl. I, Zone 2: ExnA IIC; T4
	POCC IT. ГБ05: B00387	GOST 12.2.007.0-75 GOST P 51330.10-99	[Ex ia] IIC
	DECLARATION OF CONFORMITY ->